 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MICRF001 QwikRadio Receiver/Data Demodulator Advance Information General Description The MICRF001 is a single chip OOK (ON-OFF Keyed) Receiver IC for remote wireless applications, employing Micrel's latest QwikRadiotm technology. This device is a true "antenna-in, dataout" monolithic device. All RF and IF tuning is accomplished automatically within the IC, which eliminates manual tuning, and reduces production costs. Receiver functions are completely integrated. The result is a highly reliable yet extremely low cost solution for high volume wireless applications. Because the MICRF001 is a true single-chip radio receiver, it is extremely easy to apply, minimizing design and production costs, and improving time to market. The MICRF001 uses a novel architecture that allows the receiver to demodulate signals over a wide RF band, which eliminates the need for manual tuning. This also significantly relaxes the frequency accuracy and stability requirements of the Transmitter, allowing the MICRF001 to be compatible with both SAW-based and LC-based transmitters. The receiver sensitivity and selectivity are sufficient to provide low bit error rates for decode ranges over 100 meters, equaling the performance of other more expensive solutions. All tuning and alignment are accomplished on-chip by a lowcost ceramic resonator or with an externally supplied clock reference. Initial tolerance requirements on the ceramic resonator or external clock is a modest 0.5%. The MICRF001 performance is insensitive to data modulation duty cycle. The MICRF001 may be used with such coding schemes as Manchester or 33/66% PWM. All post-detection (demodulator) data filtering is provided on the MICRF001, so no external filters need to be designed. Any one of four filter bandwidths may be selected externally by the user. Bandwidths range from 0.6kHz to 4.8kHz in binary steps tm Features * * * * * * * * * Complete UHF receiver on a monolithic chip Frequency range 300 to 440 MHz Typical range over 100 meters with monopole antenna Data rates to 4.8kbps Automatic tuning, no manual adjustment No Filters or Inductors required Very low RF re-radiation at the antenna Direct CMOS logic interface to standard decoder and microprocessor ICs Extremely low external part count Applications * * * * Keyless Entry Security Systems Remote Fan/Light Control Garage Door Openers Typical Operating Circuit 387 MHz, 1200 BAUD OOK RECEIVER Micrel Inc. * 1849 Fortune Drive San Jose, Ca 95131 * USA * tel + 1 (408) 944-0800 * fax + 1 (408) 944-0970 * http://www.micrel.com MICRF001 QwikRadio tm Micrel Ordering Information Part Number MICRF001BN MICRF001BM Pin Configuration (DIP and SOIC) Temperature Range -40C to +85C -40C to +85C Package 14-Pin DIP 14-Pin SOIC Figure 1 Pin Description Pin Number 1 2/3 Pin Name SEL0 VSSRF Pin Function Programs desired Demodulator Filter Bandwidth. This pin in internally pulled-up to VDD. See Table 1. This pin is the ground return for the RF section of the IC. The bypass capacitor connected from VDDRF to VSSRF should have the shortest possible lead length. For best performance, connect VSSRF to VSSBB at the power supply only (i.e., keep VSSBB currents from flowing through VSSRF return path). This is the receive RF input, internally ac-coupled. Connect this pin to the receive antenna. Input impedance is high (FET gate) with approximately 2pF of shunt (parasitic) capacitance. For applications located in high ambient noise environments, a fixed value band-pass network may be connected between the ANT pin and VSSRF to provide additional receive selectivity and input overload protection. (See "Application Note 22, MICRF001 Theory of Operation".) This pin is the positive supply input for the RF section of the IC. VDDBB and VDDRF should be connected directly at the IC pins. Connect a low ESL, low ESR decoupling capacitor from this pin to VSSRF, as short as possible. This pin is the positive supply input for the baseband section of the IC. VDDBB and VDDRF should be connected directly at the IC pins. This capacitor extracts the (DC) average value from the demodulated waveform, which becomes the reference for the internal data slicing comparator. Treat this as a low-pass RC filter with source impedance described in Table 1 . (See "Application Note 22, MICRF001 Theory of Operation", section 6.4). A standard 20% X7R ceramic capacitor is generally sufficient. Output data pin. CMOS level compatible. This is the ground return for the baseband section of the IC. The bypass and output capacitors connected to VSSBB should have the shortest possible lead lengths. For best performance, connect VSSRF to VSSBB at the power supply only (i.e., keep VSSBB currents from flowing through VSSRF return path). Integrating capacitor for on-chip receive AGC. The Decay/Attack time-constant (TC) ratio is nominally set as 10:1. CAGC = 10(Attack Time Constant) F. A standard 20% X7R ceramic capacitor is generally sufficient. Programs desired Demodulator Filter Bandwidth. This pin in internally pulled-up to VDD. See Table 1. This is the timing reference for on-chip tuning and alignment. Either connect a ceramic resonator between this pin and VSSBB, or drive the input with an AC coupled 0.5Vpp input clock. Use ceramic resonators without integral capacitors. See "Application Note 22, MICRF001 Theory of Operation" for details on frequency selection and accuracy. This logic pin controls the operating mode of the MICRF001. When SWEN = HIGH, the MICRF001 is in SWP mode. This is the normal (default) mode of the device. When SWEN = LOW, the device operates as a conventional single-conversion superheterodyne receiver. (See "Application Note 22, MICRF001 Theory of Operation" for details.) This pin is internally pulled-up to VDD. 4 ANT 5 VDDRF 6 7 VDDBB CTH 8 9/10 DO VSSBB 11 CAGC 12 13 SEL1 REFOSC 14 SWEN June 1998 2 MICRF001 MICRF001 QwikRadio tm Micrel ABSOLUTE MAXIMUM RATINGS Supply Voltage (VDDRF, VDDBB)...................................+7V Voltage on any I/O Pin...........................VSS-0.3 to VDD+0.3 Junction Temperature.................................................+150C Storage Temperature Range......................-65C to + 150C Lead Temperature (soldering, 10 seconds)..............+ 300C Operating Ratings Supply Voltage (VDDRF, VDDBB)....................4.75V to 5.5V Ambient Operating Temperature (TA)............-40C to +85C Package Thermal Resistance ja (14 Pin DIP)..........90C/W This device is ESD sensitive: Meets Class 1 ESD test requirements (Human Body Model, HBM), in accordance with MIL-STD-883C, Method 3015. Do not operate or store near strong electrostatic fields. Use appropriate ESD precautions. Electrical Characteristics Parameter Power Supply Operating Current Operating Current RF/IF Section Receiver Sensitivity IF Center Frequency IF Bandwidth Receive Data Rate RF Input Range Receive Modulation Duty-Cycle Maximum Receiver Input Spurious Reverse Isolation AGC Attack / Decay ratio Oscillator Turn-on Time Demod Section CTH Source Impedance CTH Source Impedance Variation Digital Section REFOSC Input Impedance Input Pullup Impedance Output Current Output High Voltage Output Low Voltage Output Tr, Tf Note 1: Unless otherwise stated, these specifications apply for Ta=-40C to 85C, 4.75 Ta= 25C Reference Oscillator powered down Note 1, 3 Note 3 MIN TYP 6.3 2 -95 2.25 1.0 MAX UNITS mA mA dBm MHz MHz 0.1 300 20 Rs = 50 ANT pin, Rs = 50 Note 2 T(Attack) / T(Decay) -20 30 0.1 0.1 SEL0=SEL1=VDD, See Table 1 -15 200k SEL0, SEL1, SWEN DO pin, Push-Pull DO pin, Iout = 1A DO pin, Iout = 1A DO pin, Cload=15pF 0.9VDD 1000k 10 200k 4.8 440 80 kbps MHz % dBm Vrms s +15 % A V 0.1VDD 10 V sec Note 2: Note 3: Sensitivity is defined as the average signal level measured at the input necessary to achieve 10e-2 Bit Error Rate (BER). The input signal is defined as a return-to-zero (RZ) waveform with 50% average duty cycle at a data rate of 2400bps. The RF input is assumed to be matched into 50. Spurious reverse isolation represents the spurious components which appear on the RF input (ANT) pin measured into 50 with an input RF matching network. Sensitivity, a commonly specified Receiver parameter, provides an indication of the Receiver's input referred noise, generally input thermal noise. However, it is possible for a more sensitive receiver to exhibit range performance no better than that of a less sensitive receiver, if the "ether" noise is appreciably higher than the thermal noise. "Ether" noise refers to other interfering "noise" sources, such as FM radio stations, pagers, etc. A better indicator of receiver range performance is usually given by its Selectivity, often stated as Intermediate Frequency (IF) or Radio Frequency (RF) bandwidth, depending on receiver topology. Selectivity is a measure of the rejection by the receiver of "ether" noise. More selective receivers will almost invariably provide better range. Only when the receiver selectivity is so high that most of the noise on the receiver input is actually thermal will the receiver demonstrate sensitivity-limited performance. June 1998 3 MICRF001 MICRF001 SEL0 0 1 0 1 SEL1 0 0 1 1 QwikRadio tm PROGRAMMABLE LPF BANDWIDTH (Hz) 600 1200 2400 4800 Micrel CTH SOURCE IMPEDANCE (OHMS) 1600k 800k 400k 200k Table 1. Nominal Characteristics Programmable LPF Bandwidth and CTH Source Impedance CTH Source Impedance in Table 1 is represented by (symbolic) resistor RSC in the MICRF001 Simplified Block Diagram. The Programmable LPF (Low Pass Filter) is also illustrated in the MICRF001 Simplified Block Diagram. MICRF001 IDD vs Frequency (Temperature=25C, VDD=5.25V, SWP Mode) 18 16 14 12 10 8 6 4 250 275 300 325 350 375 400 425 450 475 500 IDD(mA) Frequency (MHz) MICRF001 IDD vs Temperature (Frequency=315MHz, VDD=5.25V, SWP Mode) 8.5 8 7.5 7 IDD(mA) 6.5 6 5.5 5 -40 -20 0 20 40 60 85 Temperature (C) June 1998 4 MICRF001 MICRF001 QwikRadio tm Micrel Block Diagram Functional Description The block diagram illustrates the basic structure of the MICRF001. Identified in the figure are the three principal functional blocks of the IC, namely (1) UHF Downconverter, (2) OOK Demodulator, and (3) Reference and Control. Also shown in the figure are two capacitors (CTH, CAGC) and one timing component (CR), usually a ceramic resonator. With the exception of a supply decoupling capacitor, these are all the external components needed with the MICRF001 to construct a complete UHF receiver. Three control inputs are shown in the block diagram, SEL0, SEL1 and SWEN. Through these logic inputs the user can control the operating mode and programmable functions of the IC. These inputs are CMOS compatible, and are pulled-up on the IC. The inputs SEL0, SEL1 control the Demodulator filter bandwidth in four binary steps from approximately 0.6kHz to 4.8kHz, and the user must select the bandwidth appropriate to his needs. The SWEN pin allows the device to be configured in either its normal (SWP) operating mode, or in standard (FIXED) superheterodyne receiver mode. SWP operation is selected when SWEN is HIGH, and is the default mode for the IC. An example of SWP operation would be where the MICRF001 must operate with LC-based transmitters, whose transmit frequency may vary up to 0.5% over initial tolerance, aging, and temperature. In this (patent-pending) mode, the LO frequency is varied in a prescribed fashion which results in downconversion of all signals in a band 2-3% around the transmit frequency. So the Transmitter may drift up to 0.5% without the need to retune the Receiver, and without impacting system performance. Such performance is not achieved with currently available crystal-based superheterodyne receivers, which can operate only with SAW or crystal based transmitters. [Note: A range penalty will occur in installations where there exists a competing signal of sufficient strength in this small frequency band of 2-3%. This penalty also exists with superregenerative type receivers, as their RF bandwidth is also generally 2-3%. So any application for a super-regenerative receiver is also an application for the MICRF001.] June 1998 5 MICRF001 MICRF001 External Control Signals and Mode Selection QwikRadio tm Micrel For applications where the transmit frequency is accurately set for other reasons (e.g., applications where a SAW transmitter is used for its mechanical stability), the user may choose to configure the MICRF001 as a standard superheterodyne receiver (FIXED mode), mitigating the aforementioned problem of a competing close-in signal. This can be accomplished by tying SWEN to ground. Doing so forces the on-chip LO frequency to a fixed value. In such a case, the ceramic resonator would be replaced with a crystal. Generally, however, the MICRF001 can be operated with a ceramic resonator adequately, no matter whether the transmitter is LC or SAW based. Slicing Level and the CTH Capacitor Extraction of the DC value of the demodulated signal for purposes of logic-level data slicing is accomplished by external capacitor CTH and the on-chip switched-cap "resistor" RSC, indicated in the block diagram. The effective resistance of RSC varies in the same way as the Demodulator filter bandwidth, in four binary steps, from approximately 1600k to 200k. Once the filter bandwidth is selected, this "resistance" is determined; then the value of capacitor CTH is easily calculated, once the slicing level time-constant is chosen. Values vary somewhat with decoder type, but typical Slicing Level time constants range 5-50msec. Optimization of the CTH value is required to maximize range, as discussed in "Application Note 22, MICRF001 Theory of Operation", section 6.4. AGC Function and the CAGC Capacitor The signal path has automatic gain control (AGC) to increase input dynamic range. An external capacitor, CAGC, must be applied to set the AGC attack and decay time-constants. With the addition of only a capacitor, the ratio of decay-toattack time-constant is fixed at 10:1 (i.e., the attack time constant is 1/10th the decay time constant), and this ratio cannot be changed by the user. However, the attack time constant is selectable by the user through the value of capacitor CAGC. By adding resistance from the CAGC pin to VDDBB or VSSBB in parallel with the CAGC capacitor, the ratio of decay-to-attack time-constant may be varied. See "Application Note 22, MICRF001 Theory of Operation". Reference Oscillator (REFOSC) and External Timing Element All timing and tuning operations on the MICRF001 are derived from the REFOSC function. This function is a singlepin Colpitts-type oscillator. The user may handle this pin in one of three possible ways: (1) connect a ceramic resonator, or (2) connect a crystal, or (3) drive this pin with an external timing signal. The third approach is attractive for further lowering system cost if an accurate reference signal exists elsewhere in the system (e.g., a reference clock from a crystal or ceramic resonator-based microprocessor), and flexibility exists in the choice of system transmit frequency. An externally applied signal should be AC-coupled, and resistively-divided down (or otherwise limited) to approximately 0.5Vpp. The specific reference frequency required is related to the system transmit frequency, and the operating mode of the device as set by the SWEN control pin. See "Application Note 22, MICRF001 Theory of Operation" for a discussion of frequency selection and accuracy requirements. I/O Pin Interface Circuitry Interface circuitry for the various I/O pins of the MICRF001 is shown in Figures 1 through 6. Specific information regarding each of these circuits is discussed in the following subparagraphs. Not shown are ESD protection diodes which are applied to all input pins. 1. ANT Pin The ANT pin is internally AC-coupled via a 3pF capacitor, to an RF N-channel MOSFET, as shown in Figure 1. Impedance on this pin to VSS is quite high at low frequencies, and decreases as frequency increases. In the UHF frequency range, the device input can be modeled as 6.3k in parallel with 2pF (pin capacitance) shunt to VSSRF. Figure 1 ANT Pin 2. CTH Pin Figure 2 illustrates the CTH pin interface circuit. CTH pin is driven from a P-channel MOSFET source-follower biased with approximately 20A of bias current. Transmission gates TG1 and TG2 isolate the 3.3pF capacitor. Internal control signals PHI1/PHI2 are related in a manner such that the impedance across the transmission gates looks like a "resistance". The DC potential on the CTH pin is approximately 2.2V, fundamentally determined by the Vgs of the two P-channel MOSFET source-followers shown. June 1998 6 MICRF001 MICRF001 3. CAGC Pin QwikRadio tm 5. REFOSC Pin Micrel Figure 3 illustrates the CAGC pin interface circuit. The AGC control voltage is developed as an integrated current into a capacitor CAGC. The attack current is nominally 15A, while the decay current is a 1/10th scaling of this, approximately 1.5A. Signal gain of the RF/IF strip inside the IC diminishes as the voltage on CAGC decreases. By simply adding a capacitor to CAGC pin, the attack/decay time constant ratio is fixed at 1:10. Further discussion on setting the attack time constant is found in "Application Note 22, MICRF001 Theory of Operation", section 6.5. Modification of the attack/decay ratio is possible by adding resistance from CAGC pin either to VDDBB or VSSBB, as desired. 4. DO Pin The output stage for the Data Comparator (DO pin) is shown in Figure 4. The output is a 10A push-10A pull, switched current stage. Such an output stage is capable of driving CMOS-type loads. The REFOSC input circuit is shown in Figure 5. Input impedance is quite high (200k). This is a Colpitts oscillator, with internal 30pF capacitors. This input is intended to work with standard ceramic resonators, connected from this pin to VSSBB. The resonators should not contain integral capacitors, since these capacitors are contained inside the IC. Externally applied signals should be AC-coupled, amplitude limited to approximately 0.5Vpp. The nominal DC bias voltage on this pin is 1.4V. 6. Control Inputs (SEL0, SEL1, SWEN) Control input circuitry is shown in Figure 6. The standard input is a logic inverter constructed with minimum geometry MOSFETs (Q2, Q3). P-channel MOSFET Q1 is a large channel length device which functions essentially as a "weak" pullup to VDDBB. Typical pullup current is 5A, leading to an impedance to the VDDBB supply of typically 1M. Figure 2 CTH Pin Figure 3 CAGC Pin Figure 4 DO Pin Figure 5 REFOSC Pin Figure 6 SEL0, SEL1, SWEN June 1998 7 MICRF001 MICRF001 QwikRadio tm Micrel Typical Application The Figure below illustrates a typical application for the MICRF001 UHF Receiver IC. Operation in this example is at 387MHz, and may be customized by selection of the appropriate reference frequency (CR1), and adjustment of the antenna length. The value of C4 would also change, if the optional input filter is used. Changes from the 1kbps data rate may require a change in the value of R1. The Bill of Materials is shown in the accompanying chart. Typical MICRF001 Application 387 MHz Operating Frequency 1kbps Operation 6-Bit Address Decode Bill of Materials Item U1 U2 CR1 D1 R1 R2 C1 C2, C3 C4 Part Number MICRF001 HT-12D CSA3.00MG SSF-LX100LID Manufacturer Micrel Holtek Murata Lumex Bourns Bourns Panasonic Panasonic Panasonic Vendor Bourns Holtek Lumex Murata Panasonic Telephone (909) 781-5500 (408) 894-9046 (800) 278-5666 (800) 241-6574 (201) 348-7000 Description UHF Receiver Logic decoder 3.00MHz Cer. Res. RED LED 68k, 1/4W ,5% 1k,1/4W, 5% 4.7F, Dip Tant. Cap 0.47F, Dip Tant. Cap 8.2pF, COG Cer. Cap Fax (909) 781-5273 (408) 894-0838 (847) 359-8904 (770) 436-3030 (201) 348-8164 MICREL INC. 1849 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL + 1 (408) 944-0800 FAX + 1 (408) 944-0970 WEB http://www.micrel.com This information is believed to be accurate and reliable, however no responsibility is assumed by Micrel for its use nor for any infringement of patents or other rights of third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent right of Micrel Inc. This is preliminary information and a final specification has not been completed. Before making any final design determination, consult with Micrel for final specifications. June 1998 8 MICRF001 |
Price & Availability of MICRF001BM
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |